一、敷設距離橋架內電纜垂直敷設時，注意其上端每隔1.50~2m敷設一次； 水平敷設時，每隔電纜頸、尾兩端、轉彎及5~10m。 當組0在同一高度平行設備上時，各相鄰0之間應考慮保護、檢修間隔。水平設備時，離地高度一般不宜小于2.50m。 垂直設備時，地面以下1.80m處用金屬套保護，敷設在電氣專用房間(配電室、電氣豎井、技術層等)內時在外面。 對于0水平設備，宜采用荷載曲線泄放支撐。 跨度通常為1.5~3m，也可以制作大跨度橋梁8m。 另外，垂直鋪設時，其固定點間隔不得超過2m。 可無間距敷設電纜，橋架內橫斷面的電纜填充率：電力電纜不應超過40%； 控制電纜請控制在一半以下。 0與各種管道平行或者交叉的，其小凈距應當符合有關規定。

1、 When laying cables vertically within the cable tray, pay attention to laying the upper end every 1.50-2m; When laying horizontally, every cable neck, tail end, turn, and 5-10m. When group 0 is on parallel equipment at the same height, protection and maintenance intervals should be considered between adjacent 0. When using horizontal equipment, the ground clearance should generally not be less than 2.50m. When installing vertical equipment, a metal sleeve should be used to protect the area 1.80m below the ground, and when installed in electrical dedicated rooms (distribution rooms, electrical shafts, technical floors, etc.), it should be placed outside. For level 0 equipment, it is advisable to use load curve release support. The span is usually 1.5-3m, and a large-span bridge of 8m can also be made. In addition, when laying vertically, the spacing between fixed points shall not exceed 2 meters. Cable can be laid without spacing, and the cable filling rate in the cross section of the bridge should not exceed 40% for power cables; Please control the cable below half. If 0 is parallel or intersecting with various pipelines, its small clear distance should comply with relevant national regulations.

二、有異常的電纜或電壓，不得敷設在同一層橋架上。例如，有lkV以上和1kV以下異常電壓的電纜、經同一路徑向一次負載供電的雙路電源電纜異常用途電纜、應急照明和其他照明電纜，或者強電和弱電電纜，不得敷設在同一層橋架上，受條件限制設備在同一層橋架的，應當用隔板隔離。

2、 Any abnormal cables or voltages shall not be laid on the same layer of cable tray. For example, cables with abnormal voltages above 1kV and below 1kV, dual power cables supplying power to a load through the same path, cables for abnormal purposes, emergency lighting and other lighting cables, or strong and weak current cables shall not be laid on the same layer of bridge. If they are limited by conditions and installed on the same layer of bridge, they should be isolated with partitions.

三、防護方法室內選用電纜接線時，其電纜不應有黃麻或其他易燃材料的外層保護層； 在有腐蝕或罕見濕潤的地方使用電纜接線時，應根據腐蝕介質的異常情況采用相應的防護方法。 橋架使用耐腐蝕的熱鍍鋅橋架時，應使用塑料護套電纜。請勿安裝在腐蝕性氣體配管和熱配管的上方及腐蝕性液體配管的下方，條件有限時請務必采用防腐、隔熱方法。

3、 When selecting cable wiring indoors, the cable should not have an outer protective layer of jute or other flammable materials; When using cable wiring in areas with corrosion or rare moisture, corresponding protective methods should be adopted according to the abnormal situation of the corrosive medium. When using corrosion-resistant hot-dip galvanized cable trays, plastic sheathed cables should be used. Do not install above corrosive gas piping and hot piping, or below corrosive liquid piping. When conditions are limited, be sure to use anti-corrosion and insulation methods.

以上的文章由濟南航豐實業有限公司濟南電纜橋架提供分享，更多內容請關注我們：http://www.euup.cn

The above article is shared by Jinan Hangfeng Industrial Co., Ltd. Jinan Cable Tray. For more information, please follow us: http://www.euup.cn