久久久精品免费视频-99re在线视频-曰韩三级-亚洲毛片视频-日韩电影av-四虎看片

網站公告-NOTICE
聯系我們
濟南航豐實業有限公司

電話:15168870138
聯系人:龐經理

網址:http://www.euup.cn  

廠址: 德州市禹城市莒鎮產業園26棟

經銷商地址:天橋區建華五金市場東區5-1  

魯ICP備09095923號-1

新聞資訊

當前位置:首頁 / 新聞資訊

電纜橋架的支、吊架的配置要求

水平敷設時,支架間距一般不應大于2000mm。

When laying horizontally, the spacing between supports should generally not exceed 2000mm.

彎頭附近應增設支架,彎頭半徑小于300mm時,應在彎頭兩端各300-600mm處設置一個支架。

A bracket should be added near the elbow. When the radius of the elbow is less than 300mm, a bracket should be set at 300-600mm at each end of the elbow.

02

垂直單層敷設時,支架間距不應超過2000mm。多層時應通過計算確定。

When laying vertically in a single layer, the spacing between supports should not exceed 2000mm. When there are multiple layers, they should be determined through calculation.

立柱應與托盤、梯架層間距離相適應,以便多層布置。

The distance between the columns and the pallets and ladder layers should be suitable for multi-layer layout.

吊桿不應使用小于10mm的圓鋼,應有防晃措施,端部應有固定措施。

The suspension rod should not use round steel smaller than 10mm, and anti sway measures should be taken. The end should have fixing measures.

豎井內敷設時,每3-5層設置一個承重支架,不應安裝在固定電纜的橫擔上。

When laying in the vertical shaft, a load-bearing bracket should be installed every 3-5 layers and should not be installed on the cross arm of the fixed cable.

固定支架與預埋件焊接時,焊縫應滿足質量要求,長度不應少于25mm。

When welding fixed brackets and embedded parts, the weld seam should meet quality requirements and the length should not be less than 25mm.

使用膨脹螺栓時應符合相關標準規定。

The use of expansion bolts should comply with relevant standards and regulations.

支架安裝應垂直、無明顯扭曲,高度誤差不超過公差要求。

The bracket installation should be vertical, without obvious distortion, and the height error should not exceed the tolerance requirements.

支架的設計和安裝應滿足其強度、剛度和穩定性的要求。

The design and installation of the bracket should meet its requirements for strength, stiffness, and stability.

主體鋼結構上不得焊接支、吊架,應征得結構許可。

Welding of supports and hangers is not allowed on the main steel structure, and a structural professional permit must be obtained.

支、吊架的設計應根據托盤、梯架的規格、層數、跨距等條件進行配置,并滿足載荷要求。

The design of supports and hangers should be configured according to the specifications, number of layers, span, and other conditions of pallets and ladders, and meet the load requirements.

托臂的開孔位置應協調層間距離的要求。立柱可預留可調節的長孔。

The opening position of the support arm should be coordinated with the requirements of interlayer distance. The column can reserve adjustable long holes.

支、吊架的規格和型號應在滿足載荷條件下,根據項目的實際情況選擇。

The specifications and models of supports and hangers should be selected according to the actual situation of the project while meeting the load conditions.

金屬支、吊架應進行防腐處理,特別是戶外和潮濕環境的。

Metal supports and hangers should undergo anti-corrosion treatment, especially in outdoor and humid environments.

支、吊架的設計計算和試驗應驗證其滿足強度、剛度和穩定性要求。

The design calculation and testing of supports and hangers should verify that they meet the requirements of strength, stiffness, and stability.

 
qq
售前咨詢熱線
15168870138
售后咨詢熱線
13465410318
主站蜘蛛池模板: 第四色成人网 | 亚洲精品成人一区 | 亚洲综合国产一区在线 | 亚洲精品毛片久久久久久久 | a级一片 | 久久99国产亚洲精品观看 | 国产精品免费看久久久香蕉 | 99视频免费在线观看 | 国产一区二区免费视频 | 欧美无极品 | 欧美黄免在线播放 | 久草免费资源站 | 抱着cao才爽免费观看 | 香蕉久久一区二区不卡无毒影院 | 免费观看的毛片手机视频 | 久热香蕉精品视频在线播放 | 成人性生免费视频 | 精品91一区二区三区 | 国产只有精品 | 日本aaaa片毛片免费观看 | 九草在线免费观看 | 老色99久久九九精品尤物 | 国产亚洲欧美另类久久久 | 99久久一区二区精品 | 欧美18毛片免费看 | 国产亚洲91| 国产伦码精品一区二区三区 | 伊人久久大香线焦综合四虎 | 色拍拍噜噜噜aⅴ在线观看 色青青草原桃花久久综合 色婷婷91 | 国产精品成人免费视频不卡 | 国产乱子伦露脸对白在线小说 | 纯欧美一级毛片_免费 | 久久国产精品一国产精品 | 中文字幕有码视频 | 欧美成人性色xxxxx视频大 | 午夜三级在线 | 美女黄页网站免费进入 | 国产高清在线观看 | 亚洲欧美在线观看播放 | 日本亚洲欧美国产日韩ay高清 | 亚洲欧美一区二区三区不卡 |